Chemical Pump-manufacture,factory,supplier from China

Mark III is diagnosed global as the surest name in ANSI chemical process pumps.

1. The 3196 ANSI Series is available in a wide range of sizes, capacities and materials to fit virtually any process-fluid application.

1.Application: Chemical ProcessingGeneral IndustriesMiningWater ResourcesPower GenerationPrimary MetalsPulp and PaperOil and Gas2.Capacities to 7000 GPM (1590 m³ /h)Heads to 730 feet (223 m)Temperatures to 700° F (371° C)Pressures to 375 PSIG (26 bar)3.Available Size:6’’-16’’4.Part NameMaterialDuctile Iron316SSCD4MCuAlloy 20NickelHastelloy CTitaniumCasing316SSCD4MCuAlloy 20NickelHastelloy CTitaniumImpeller316SSCD4MCuAlloy 20NickelHastelloy CTitaniumCover316SSCD4MCuAlloy 20NickelHastelloy CTitaniumFrameDuctile IronBearing HousingDuctile IronAdaptorDuctile IronShaft316SS/4140Sleeve316SSCD4M

Fully open impeller is the excellent design for the chemical manner industries services. Ideally suited for corrosives and abrasives, handles solids and stringy fibers conveniently. Permits for simple recuperation of clearances while wear takes area.

When the 3196 ANSI Pump was first introduced in 1961, it immediately became the standard in the industry.  Today, the number of installations attest to its remarkable performance.  Users in chemical, petrochemical, pulp & paper, primary metals, food & beverage and general industries know they can make no better choice than the best.1. Application: Chemical ProcessingGeneral IndustriesMiningWater ResourcesPower GenerationPrimary MetalsPulp and PaperOil and Gas2.Capacities to 7000 GPM (1590 m³ /h)Heads to 730 feet (223 m)Temperatures to 700° F (371° C)Pressures to 375

Product DescriptionProven PerformanceUsers in chemical, petrochemical, pulp & paper, primary metals, food & beverage and general industries know they can make no better choice than the best -  Model 3196.Power Ends are the result of over 160 years of design experience, customer interaction, and continuous improvement.  Customers get extended MTBF (Mean Time Between Failure) and lower LCC (Life Cycle Cost)….guaranteed!

The Mark III chemical process pump is a horizontal, cease suction, unmarried degree, centerline discharge, centrifugal pump.

The Mark III chemical process pump is a horizontal, end suction, single level, centerline discharge, centrifugal pump.

Mark III is recognized international as the most suitable name in ANSI chemical method pumps.

Our seal chambers permit seals to run cooler with higher face lubrication.

3196 takes fully open impeller which is the best design for the chemical process industries services. Ideally suited for corrosives and abrasives, handles solids and stringy fibers with ease.

Conforming to ASME(ANSI) B73.1, the Mark 3 chemical process pump provides outstanding hydraulic performanceand many proven reliability- and performance-enhancing features. And it is recognized international as the most suitable name in ANSI chemical method pumps.1.Application: Chemical ProcessingGeneral IndustriesMiningWater ResourcesPower GenerationPrimary MetalsPulp and PaperOil and Gas2.Capacities to 7000 GPM (1590 m³ /h)Heads to 730 feet (223 m)Temperatures to 700° F (371° C)Pressures to 375 PSIG (26 bar)3.Available Size:6''-16''

Mark III is identified worldwide because the most advantageous name in ansi chemical procedure pumps.

The LF3196 process pump line is specifically designed to provide superior performance for low flow services of the Chemical Process Industries.1. Application: Chemical ProcessingGeneral IndustriesMiningWater ResourcesPower GenerationPrimary MetalsPulp and PaperOil and Gas2.Capacities to 220 GPM (50 m3/h)N Heads to 925 feet (282 m)N Temperatures to 700° F (371° C)N Pressures to 450 PSIG (3102 kPa) 3. Available Size:8’’-13’’ 4.Radial vane impeller5.CASING#150RF/#300RF flange6.Seal ChamberStandard bore and big bore 

The mark 3 chemical system pump presents high-quality hydraulic overall performance, unrivaled reliability and coffee overall price of possession.

The Mark 3 chemical process pump offers first-rate hydraulic performance, unmatched reliability and occasional total fee of ownership.Conforming to ASME(ANSI) B73.1,the Mark 3 includes many confirmed reliability- and overall performance-improving functions.1.Application:  • Acid transfer• Brine• Chemical processing• Petrochemical processing• Corrosive services• Food and beverage processing• Hydrocarbon processing• Pharmaceuticals Polymers• Pulp and paper• Seawater• Slurries• Solvents• Steel and primary metals• Water and wastewater treatment 2.Operating Parameters• Flows to

The 3196 ANSI Series is available in a extensive variety of sizes, capacities and materials to match sincerely any manner-fluid software.1.Application:  Chemical ProcessingGeneral IndustriesMiningWater ResourcesPower GenerationPrimary MetalsPulp and PaperOil and Gas 2.Capacities to 7000 GPM (1590 m³ /h)Heads to 730 feet (223 m)Temperatures to 700° F (371° C)Pressures to 375 PSIG (26 bar)  3.Available Size:6’’-15’’ 4.ImpellerDesigned for long-term, maintainable performance and minimum hydraulic loads formaximum reliability. CASING• Top centerline discharge for air

Chemical Process PumpsDesigned for Total Range ofIndustry ServicesI Capacities to 7000 GPM (1364 m 3 /h)I Heads to 730 feet (223 m)I Temperatures to 700°F (371° C)I Pressures to 375 PSIG (2586 kPa)Product Description:The 3196 ANSI series is to be had in a huge variety of sizes, capacities and materials to match virtually any system-fluid utility.ImpellerDesigned for long-term, maintainable performance and minimum hydraulic loads formaximum reliability.CASING• Top centerline discharge for air handling, self-venting.• Class 150 pumps have Class 300 wall thickness as standard.• Back pull-out desi

We provide innovative pumping solutions to business partners in the following industries:• Oil and Gas• Hydrocarbon Processing• Pulp and Paper• Power Generation• General Industry• Chemical Process Industry• Watera.Closed Impelleris used for pumping clean liquids or liquids containing some impurities.For pump types:APPEPPb.Open Impelleris designed for liquids containing solid particles, abrasive liquids or stock up to 8 % consistency.For pump types:APPARPASPEPPc.Special Open Impelleris suitable for liquids containing larger solid particles and long fibers, abrasive liquids or stock up to 8 % co

Absolutely open impeller is the first-class layout for the chemical process industries services. Ideally fitted for corrosives and abrasives, handles solids and stringy fibers simply. Lets in for easy healing of clearances while wear takes place. Lower back pump-out vanes reduce stress at the shaft seal, reduce axial thrust at the bearings.Our seal chambers permit seals to run cooler with better face lubrication. Keep solids, air and vapors faraway from the seal faces for prolonged seal lifestyles.Our electricity ends design maximizes reliability and mean time among failure (mtbf).

ImpellerDesigned for lengthy-time period, maintainable overall performance and minimum hydraulic hundreds forMost reliability.Casing• Top centerline discharge for air handling, self-venting.• Class a hundred and fifty pumps have class 300 wall thickness as trendy.• Returned pull-out layout.• Indispensable toes.Seal chamberDesigned for favorable seal environment —right warmness dissipation and lubrication of seal faces.The design ought to also be able to manage hard offerings: beverages containing solids, air or vapors.Energy endDesigned for optimum bearing lifestyles, powerful oil cooling, and

Fully open impeller is the best design for the chemical process industries services. Ideally suited for corrosives and abrasives, handles solids and stringy fibers with ease. Allows for simple restoration of clearances when wear takes place.

Our Pump Replacement elements are reliable, price effective alternative parts which are interchangeable with many widely known pump manufacturers.We manufacture more than a few alternative elements together with shafts, casings, impellers, stuffing container covers, sleeves, labyrinth seals, repellers, backplates, fans and lots of extra.

The mark III chemical technique pump is a horizontal, give up suction, unmarried level, centerline discharge, centrifugal pump.