Higher Volume Output Pump-manufacture,factory,supplier from China

The hydraulic design of two-phase flow pulp pump adopts the principle of “Relative suction and relative blocking”in the theory of two-phase flow, so that the hydraulic performance of the flow parts of the pump conforms to the law of solid-liquid two-phase flow, thus reducing the slurry flow parts of the erosion and wear, greatly improving the efficiency and service life of the pump, the pump series has the following notable features:1.High efficiency and energy saving: The running efficiency is 3-10 percentage points higher than the average of the ordinary pulp pump, the energy saving and cons

ANSI Mark III 4x3-10H bare shaft pump in WCB material, other materials like CD4M, CF8M, A20 etc are all available. And our pumps are 100% interchangeble with leading enterprise's one.If any needs, pls contact me for quotation.

 The working principle of the engine water pump: Through the belt pulley to drive the pump bearing and the impeller to rotate, the cooling liquid in the pump is driven by the impeller to rotate together, and is thrown to the edge of the pump shell under the effect of Centrifugal Force, at the same time generating certain pressure, and then it comes out of a drain or a pipe.

Operating Parameters• Flows to 4540 m3/h (20 000 US gpm) • Heads to 215 m (700 ft) • Pressures to 27 bar (400 psi) • Temperatures from -73°C (-100°F) to 370°C (700°F) • Discharge sizes from 25 mm (1 in) to 200 (8 in)  The material of wet ends like A20, CD4M, 316SS, Titanium, Hastelloy C, Nickel etc are all available, if any needs, I'd like to offer you for your reference.

PerformanceHead up to 110 m. Temperature max. 180 °C. Capacity up to 2000 l/s. Operating frequencies 50 or 60 Hz. Pressure up to 1.6 MPa, depending on material and size.

Main applicationsBoiler feedHigh-pressure unit charge in refiningEthylene shippingOnshore and offshore waterfloodOffshore crude shippingOur pump is 100% interchangeble with original one, if any needs, pls contact me for quotation.

Besides casting pump parts and maching pump parts, we also supply gasket, bearing, O-ring, oil seal etc accessories for assembling a pump.Pls let me know if any needs, I'd like to offer you for your reference.

It seems there might be a slight mix-up with the pump terminology. As of my last update in January 2022, there isn't a widely recognized "WPP Pump" specifically within the domain of industrial or commercial pump systems. However, pumps with the prefix "WPP" could be a colloquial term, an abbreviation, or perhaps referring to a specific model or brand known in certain industries.To provide more accurate information, could you confirm if you're referring to a specific type of pump or a brand?

First. Classification by impeller number 1. Single-stage pump: that is, there is only one impeller on the pump shaft. 2. Multi-stage pump: that is, there are two or more impellers on the pump shaft, and the total lift of the pump is the sum of the lifts generated by n impellers. Second, classified according to work pressure 1. Low-pressure pump: the pressure is less than 100m H2O; 2. Medium pressure pump: the pressure is between 100 and 650 meters of water column; 3.

Our pump can meet many kinds of different application, take the following example:Soda Pump                                                                          ANSI B.73.1Size In/ Out : 10 Inch/ 8 Inch Flange ANSI 150 FFDuty Point:Liquid : Caustic Soda/ Sulphamite AcidCapacity : 8 M3/Min ( 480 M3/H )Head : 40 Meter ( 131 Ft )Temperature : 80 deg CPH : 4 – 10SG : 1.47If any needs, pls let me know.

Users in chemical, petrochemical, pulp & paper, primary metals, food & beverage and general industries choose our pumps because of its good quality and price, so contact me if you have any needs.

Our pump parts are 100% interchangeble with leading enterprise's one, so if any needs of casing, impeller, cover etc, pls feel free to contact me for quotation.